New industry Technology regarding to Bussmann fuse, ABB breakers, Amphenol connectors, HPS transformers, etc.
Mechanical Selection · Installation Guide
Most fuse returns are not electrical. They are fuses that were correctly rated and did not fit — a body 25 mm too tall for the enclosure, tags 3 mm too far apart for the holder, or a blade drilling that will not seat in the base. This guide covers the five measurements that decide whether a fuse will actually install, with the dimensions of the most common Bussmann families in one place.
The selection process usually runs electrical first: current, I²t, voltage. Then it stops, and someone orders a part that meets every electrical requirement and does not physically fit. The reason is that catalogue tables are organised by electrical ratings, while the drawings are organised by body size — and the two are not in the same place, so the mechanical check gets skipped.
This article sets out the mechanical decision in the order it should be made: interface first, then body, then clearance. It then gives verified dimensions for the families that account for most orders.
| Measurement | What it decides | Failure mode if wrong |
| Interface type | Whether the fuse can connect at all: ferrule, bolted tag, NH blade, PCB pin | Fuse physically cannot be installed |
| Centre distance | Distance between tag centres or blade centres | Tag will not enter the clamp, or clamps at one end only |
| Overall length with tags | Space needed between busbars, not just body height | Body fits, tags do not; door will not close |
| Body width and depth | Side-by-side pitch and clearance to the panel | Adjacent fuses touch, or the row does not fit |
| Clearance to earthed metal | Dielectric clearance at the system voltage | Passes electrical test at 690 V, fails at 1000 V |
Two of these — interface type and centre distance — are decided by the holder or base you already have, and they are the ones people get wrong when they specify a fuse by part number alone. The other three are enclosure constraints and can usually be solved by rearranging the panel.
Four interface types cover the fuse families most commonly ordered for industrial and PV work. Each one has a different set of dimensions that must match, and they are not interchangeable.
| Interface | Typical families | Matching dimensions | Holder / base |
| Cylindrical ferrule 10 × 38 mm | PV-A10, PVM, 10 × 38 industrial | 38.0 ± 0.6 length, 10.3 ± 0.1 diameter | Modular DIN holder (CHPV, BMM603) |
| Cylindrical ferrule 14 × 65 mm | PV-A14LF (1300–1500 V) | 65 mm length, 14 mm diameter | 14 × 65 holder (not the 10 × 38 one) |
| Bolted tag, DIN 43653 | 170M sizes 000 to 3 | Tag centre distance, tag thickness, hole diameter | Fixed-centre base (170H3003–170H3006) or direct bolt |
| NH blade | PV-ANH1/2/3, BSF-NH | Blade thickness and drilling (-B, -BL suffix) | NH base of matching size |
The blade suffix deserves its own warning. On the NH PV range, PV-100ANH1, PV-100ANH1-B and PV-100ANH1-BL are electrically identical and mechanically different: plain blade, blade with bolt holes, and a third blade pattern. All three are sold at the same rating, and only one will seat in a given base. When a customer reports “the fuse does not fit but the rating is right”, this is usually why.
The 10 × 38 mm ferrule is the standard small fuse in both PV combiners and industrial control panels. Its dimensions are simple and, usefully, identical across mounting variants.
| Variant | Length | Diameter / width | Notes |
| Cylindrical (-xA10F) | 38.0 ± 0.6 mm | 10.3 ± 0.1 mm | Fits any compliant holder |
| PCB single-ended (-1P) | 12.7 mm pin pitch | 38 mm body | One end soldered, one end clipped |
| PCB double-ended (-2P) | 39.2 ± 0.9 mm | 16.38 mm pin spacing | Both ends soldered |
| Bolt fixing (-T) | 58.9 ± 0.9 mm overall | 51.1 ± 1.4 mm bolt centres | 6 mm bolts, direct to busbar |
The bolt-fixing variant is the one that surprises: the body is still 38 mm, but the overall item is 58.9 mm long because of the end tags, and the bolt centres are 51.1 mm. A panel designed with 45 mm spacing will not accept it even though “it is a 10 × 38 fuse”.
For holders, the modular CHPV and BMM603 families mount on 35 mm DIN rail and stack side by side. Their own widths set the pitch: 17 mm per pole on the BMM603, 40 mm for two poles and 60 mm for three, with a body height around 77 mm and 95 mm depending on the terminal version. A three-pole block therefore needs 60 mm of rail per fuse position, not 51 mm.
At 1300–1500 V d.c. the small ferrule is replaced by a 14 × 65 mm body. The step is significant in a combiner: the holder changes, the pitch changes, and the depth required behind the rail increases.
Three mounting variants exist — cylindrical for a modular holder, bolt fixing, and a cylindrical version with 10 mm fixings for a specific holder family. As with the 10 × 38 mm range, the electrical data are shared across variants but the mechanical envelope is not, and the bolt-fixing version is longer overall than the cylinder.
The practical consequence for a combiner retrofit is straightforward: converting from 1000 V to 1500 V strings usually means replacing the holders, not just the fuses, and the new holders take more rail length per pole. If the combiner was sized for 12 string positions at 10 × 38 mm, it may only take 9 or 10 at 14 × 65 mm.
The two smallest 170M bodies are the ones most often installed in tight spaces, and their dimensions are worth memorising.
| Dimension | Value | Why it matters |
| Body height | 79.0 ± 1.0 mm | The number that appears in the drawing and is most often quoted |
| Overall height with tags | 96 mm maximum | Adds 17 mm — the difference between fitting and not fitting |
| Body width | 36.3 mm | Sets the side-by-side pitch; add clearance for convection |
The 17 mm difference between body height and overall height is where installations fail. A busbar spacing designed from the body height alone leaves the tags touching the panel door, and the door is usually earthed. Always use the overall height for clearance calculations and the body height only for the fuse's own footprint.
Above size 00 the dimensions step up, and the step is not uniform: a size 1* body is not simply “size 00 plus 25 mm”, it has a different tag arrangement and a different fuseholder requirement. This is why a voltage-class change from 690 V to 1000 V at 400 A — which moves the part from size 00 to size 1* — is a mechanical change as much as an electrical one.
NH blade fuses (sizes NH1, NH2, NH3) are specified by the base they fit, not by a body dimension, because the blade pattern is standardised. The dimensions that matter are the blade thickness, the blade height, and — critically — the drilling pattern, which is what the -B and -BL suffixes describe.
The XL styles used above 400 A in PV work are bladed and bolted links in sizes 01, 2 and 3. A size 01 part has an overall length of 127 ± 3 mm without tags and 189 ± 3 mm with, and a maximum height of 46.5 mm. The jump from 127 to 189 between “body only” and “with tags” is 62 mm, which is the largest ratio in any family covered here — a reminder that the drawing, not the body size, is the thing to read.
Clearance requirements scale with system voltage, and they are the reason a 690 V layout cannot simply be reused at 1000 V even when the new fuse happens to be the same size.
Three clearances matter: phase to phase, phase to earth, and across the fuse itself (terminal to terminal). The first two are set by the installation standard and the pollution degree; the third is built into the fuse and is the reason the higher-voltage part is longer. When a panel is upgraded from 690 V to 1000 V, the phase-to-phase spacing often needs to increase even if the fuses stay the same physical size, because the standard's clearance table is indexed on voltage, not on component size.
The last point is worth restating: holder current rating is independent of fuse current rating, and a holder that accepts the body may not be rated for the current. This is a common error in small combiners where the holder was chosen for the 10 × 38 mm format without checking its ampere rating.
| Family | Body | Key dimensions | Mounting |
| PV-A10 (cylinder) | 10 × 38 mm | 38.0 ± 0.6 × 10.3 ± 0.1 | Modular holder, DIN rail |
| PV-A10-T (bolt) | 10 × 38 mm | 58.9 ± 0.9 overall, 51.1 ± 1.4 centres | Busbar, 6 mm bolts |
| PV-A10-2P (PCB) | 10 × 38 mm | 39.2 ± 0.9, pin pitch 16.38 | Through-hole PCB |
| PV-A14LF | 14 × 65 mm | 65 × 14 nominal | 14 × 65 holder |
| 170M size 000/00 | square body | 79.0 ± 1.0 body, 96 max overall, 36.3 wide | Bolted tags, DIN 43653 |
| PV/BSF size 01XL | 01 bladed | 127 ± 3 body, 189 ± 3 overall, 46.5 max height | Blade base or busbar |
| BMM603 block | 10 × 38 base | 17 mm per pole, 40 mm 2-pole, 60 mm 3-pole | 35 mm DIN rail or screw |
Twelve strings at 10 × 38 mm, two poles per string (positive and negative), plus a combiner output fuse. The arithmetic that decides whether it fits goes like this.
This is the point where a combiner design usually changes: not because the electrical sizing was wrong, but because 24 positions at 17 mm plus an output base does not fit in a 500 mm enclosure once wiring space is included. The fix is a second rail or a larger enclosure, and it costs far less when discovered at design time.
Switching those strings to 1500 V moves them to 14 × 65 mm bodies. The holders are wider, the depth behind the rail increases, and the same 12 strings may need 20–25% more rail. A combiner designed for 1000 V rarely converts to 1500 V without a mechanical redesign.
Modular holders clip to 35 mm DIN rail and their width sets the pitch. Three practical constraints apply beyond the arithmetic:
| Constraint | Effect |
| Holder width per pole | Sets the minimum pitch; 17 mm is typical for a 10 × 38 mm single pole |
| Terminal access | A screwdriver needs 15–20 mm above the terminal; adjacent holders can block it |
| Thermal derating | Packed holders run hotter than spaced ones; where the catalogue specifies spacing, it is for a reason |
The second row is the one that gets overlooked. A combiner that fits 24 holders into 408 mm may be impossible to wire, because the torque driver cannot reach the terminals. The usual compromise is groups of six with 20 mm gaps, which brings the rail requirement back up.
Two different clearance requirements apply to the same gap, and the larger one governs.
Dielectric clearance is set by the system voltage and the pollution degree. It is a minimum distance in air, and it does not care about current. Upgrading a panel from 690 V to 1000 V increases this requirement even if the fuse body size stays the same.
Thermal clearance is set by watts loss. Two fuses dissipating 70 W each, mounted 5 mm apart, heat each other and both run hotter than the catalogue curve assumes. The remedy is either physical spacing or a current derating, and the catalogue usually states which.
In a 690 V panel both requirements are modest and the fuse spacing is often set by the holder rather than by either requirement. In a 1000 V or 1250 V panel the dielectric requirement grows faster than the thermal one and starts to govern — which is why higher-voltage panels look conspicuously spacious even when the components are the same physical size.
A fuse that fits but is not tightened correctly will run hot, and the heat is often attributed to the fuse. Bolted-tag fuses transmit their current through the tag-to-busbar interface, and that interface has a specified torque.
The diagnostic in the field is a simple one: if the fuse body is discoloured near a terminal but the element is intact, the problem is the joint, not the fuse. Replacing the fuse without addressing the torque will reproduce the failure.
This retrofit appears whenever a 690 V system is upgraded to 1000 V at around 400 A, because the current rating stays the same and the body size steps up.
| Item | Before (690 V, 400 A) | After (1000 V, 400 A) | Consequence |
| Body size | 00 | 1* | Taller and wider; new base required |
| Pre-arcing I²t | 18,000 A²s | 42,000 A²s | Device I²t check must be redone |
| Watts loss | 70 W | 75 W | Enclosure thermal budget changes |
| Base / holder | Size 00 base | Size 1* base | Different fixing centres; drilling changes |
| Clearances | 690 V spacing | 1000 V spacing | Row pitch may need to increase |
Four of the five rows cost money and one of them — the I²t check — is a safety issue. A retrofit that changes only the fuse and reuses the base will not physically assemble, and one that changes the base but not the clearance may fail a dielectric test at commissioning.
The following list is what to take to site before ordering. It takes ten minutes and prevents most returns.
| # | Record | Note |
| 1 | Old fuse marking, photographed | Includes the voltage and class, not just the amperes |
| 2 | Old fuse overall length, tags included | Not the body length |
| 3 | Tag centre distance and tag thickness | Use a caliper, not a ruler |
| 4 | Holder or base part number | Its current rating matters as much as its size |
| 5 | Pitch to adjacent fuse positions | Check both electrical and thermal spacing |
| 6 | Depth to door, including door-mounted devices | Compare with overall height plus clearance |
Can I use a 10 × 38 mm holder for a 14 × 65 mm fuse?
No. Different diameter and length; the holder cannot clamp either end.
Why is the overall length so much greater than the body length?
The tags or blades extend beyond the body, and they are the part that must reach the clamp. For size 01XL the difference is 62 mm.
Does a higher current rating always mean a larger body?
Within one voltage class, yes. Across classes it can go the other way: a 400 A 690 V body (size 00) is smaller than a 400 A 1000 V body (size 1*).
How much clearance do fuses need side by side?
Enough to avoid mutual heating. The catalogue gives a recommended pitch; if the panel cannot provide it, derate the current rather than ignoring the heat.
Is the body height or the overall height used for enclosure depth?
Overall height, always, plus clearance to the door for voltage. Body height is only the fuse footprint.
Mechanical selection is four questions in order: what interface does the holder accept, what body size does the electrical choice force, what is the overall length including tags, and what clearances does the system voltage require. Answer them before the part number goes into the BOM.
The dimensions in this article are the ones that most often cause a return: the 17 mm between body and tag on a size 00, the 62 mm between body and tag on a size 01XL, the 60 mm rail pitch of a three-pole block, and the 10.3 mm diameter that will not fit a 14 mm holder. None of them appear in the electrical tables, and all of them decide whether the fuse installs.
New industry Technology regarding to Bussmann fuse, ABB breakers, Amphenol connectors, HPS transformers, etc.